一、水性涂料涂裝生產線的工藝設計的優點：

1、 The advantages of process design for water-based coating production lines:

1.操作人員有健康保證：水性涂料僅采用少量低毒性醇醚類有機溶劑，改善了涂裝生產線的作業環境，有利于工作人員的健康。

1. Health assurance for operators: Water based coatings only use a small amount of low toxicity alcohol ether organic solvents, which improves the working environment of the coating production line and is beneficial to the health of workers.

2.易清洗：水性涂料涂裝工具可用水清洗，大大減少清洗溶劑的消耗。

2. Easy to clean: Water based coating tools can be cleaned with water, greatly reducing the consumption of cleaning solvents.

3.環保要求達標：以水作為稀釋劑及用水清洗噴涂涂裝設備器具，一般的水性涂料有機溶劑(占涂料)在10%～15%之間，而現在的陰極電泳涂料已降至1.2%以下，有機溶劑大幅度降低，節省資源效果顯著，減少了涂裝廢氣處理對大氣的污染，更能達到國家環保要求，從而保護環境。

3. Environmental protection requirements meet standards: Water is used as a diluent and water is used to clean spraying and painting equipment and equipment. Generally, the organic solvent (accounting for 10% to 15% of the coating) in water-based coatings is between 10% and 15%, while the current cathodic electrophoretic coatings have decreased to below 1.2%. The organic solvent has been greatly reduced, resulting in significant resource savings and reduced air pollution caused by coating waste gas treatment. This can better meet national environmental protection requirements and protect the environment.

4.耐腐蝕：涂裝電泳線的涂料可以對復雜的工件進行涂裝，內腔、焊縫、棱角、棱邊部位都能涂上一定厚度的涂膜，提高了工件的耐腐蝕性。

4. Corrosion resistance: The coating of electrophoretic lines can be applied to complex workpieces, and a certain thickness of coating film can be applied to the inner cavity, welds, edges, and edges, improving the corrosion resistance of workpieces.

5.附著力強：水性涂料在濕表面和潮濕環境中可以直接涂覆施工，水性涂料對材質表面適應性好，涂層附著力強。

5. Strong adhesion: Waterborne coatings can be directly applied on wet surfaces and humid environments. Waterborne coatings have good adaptability to material surfaces and strong coating adhesion.

6.減少火災危害：水性涂料以水作溶劑，節省大量資源，水性涂料消除了施工時火災危險性。

6. Reduce fire hazards: Water based coatings use water as a solvent, saving a lot of resources. Water based coatings eliminate the fire hazards during construction.

二、水性涂料涂裝生產線的工藝設計的缺點：

2、 Disadvantages of process design for water-based coating production lines:

1.水性涂料電導率高，使用靜電噴涂時，需要絕緣等特殊處理措施。

1. Waterborne coatings have high conductivity, and special treatment measures such as insulation are required when using electrostatic spraying.

2.因為水的緣故，容易滋生細菌，因此要注意防腐防霉。

2. Due to water, it is easy to breed bacteria, so it is important to pay attention to anti-corrosion and mold prevention.

3.表面張力打，對施工過程中的材質基材表面清潔度要求高，污染易使涂膜產生縮孔。

3. Surface tension testing requires high surface cleanliness of the material substrate during the construction process, and contamination can easily cause shrinkage of the coating film.

4.水性涂料蒸發潛熱大，作為稀料的水揮發性不好，容易引起流掛、針孔、起泡等涂層缺陷；流平及固話時，能量消耗大，碳排放量增加，而且對涂裝生產線的環境、濕度要求高。

4. Water based coatings have a high latent heat of evaporation, and the water used as a diluent has poor volatility, which can easily cause coating defects such as sagging, pinholes, and foaming; When leveling and using fixed lines, energy consumption is high, carbon emissions increase, and high requirements are placed on the environment and humidity of the painting production line.

5.水性涂料腐蝕性強，對涂裝設備腐蝕性大，運輸途中，輸送管路的腐蝕性強，需要采用不銹鋼管，做好防護措施，設備改造大。

5. Waterborne coatings have strong corrosiveness and are highly corrosive to painting equipment. During transportation, the corrosion of the conveying pipeline is strong, and stainless steel pipes need to be used. Protective measures should be taken, and equipment renovation should be carried out.

6.水的粘度受剪切力影響變化很大，在收到高剪切力作用時，水性涂料的粘度會下降很多，會對輸調漆系統帶來很大的影響。

6. The viscosity of water is greatly affected by shear force, and when subjected to high shear force, the viscosity of water-based coatings will decrease significantly, which will have a significant impact on the paint transportation and blending system.

7.室溫低于5攝氏度以下時不宜存儲，容易凍壞。

7. When the room temperature is below 5 degrees Celsius, it should not be stored as it is prone to freezing damage.

感謝您的閱讀，此文的文章來源：機器人涂裝線更多的內容和問題請點擊：http://www.qzxcdz.com我們會繼續努力的為您提供服務，感謝您的支持！

Thank you for reading. The source of this article is Robot Coating Line. For more information and questions, please click: http://www.qzxcdz.com We will continue to work hard to provide you with services. Thank you for your support!

上一篇：涂裝設備流水線中故障問題怎么解決？
下一篇：選購?fù)ㄟ^式拋丸機要注意什么？